TNF alpha Kit ELISA

N° du produit ABIN456702

Détail du produit TNF alpha Kit ELISA

Antigène: TNF alpha (Tumor Necrosis Factor alpha (TNF alpha))

Reactivité: Porc

Méthode de détection: Colorimetric

Type de méthode: Sandwich ELISA

Gamme de detection: 31.2-2000 pg/mL

Seuil minimal de détection: 31.2 pg/mL

Application: ELISA

Fonction: This immunoassay kit allows for the specific measurement of porcine TNF-alpha concentrations in cell culture supernates, serum, tissue homogenates and plasma.

Type d'échantillon: Cell Culture Supernatant, Serum, Tissue Homogenate, Plasma

Analytical Method: Quantitative

Specificité: This assay recognizes recombinant and natural porcine TNF-alpha.

Réactivité croisée (Details): No significant cross-reactivity or interference was observed.

Attributs du produit: Sus scrofa,Pig,Tumor necrosis factor,Cachectin,TNF-alpha,Tumor necrosis factor ligand superfamily member 2,TNF-a,TNF,TNFA,TNFSF2

Ingrédients: Reagent (Quantity):

• Assay plate (1),
• Standard (2),
• Sample Diluent (1×20 mL),
• Assay Diluent A (1×10 mL),
• Assay Diluent B (1×10 mL),
• Detection Reagent A (1×120 μL),
• Detection Reagent B (1×120 μL),
• Wash Buffer(25 x concentrate) (1×30 mL),
• Substrate (1×10 mL),
• 2 Stop Solution (1×10 mL),
• Plate sealer for 96 wells (5),
• Instruction (1)

Matériel non inclus: Microplate reader. Pipettes and pipette tips. EP tube Deionized or distilled water.

Information d'application

Volume d'échantillon: 100 μL

Plaque: Pre-coated

Protocole: This assay employs the quantitative sandwich enzyme immunoassay technique. A monoclonal antibody specific for TNF-alpha has been pre-coated onto a microplate. Standards and samples are pipetted into the wells and any TNF-alpha present is bound by the immobilized antibody. An enzyme-linked monoclonal antibody specific for TNF-alpha is added to the wells. Following a wash to remove any unbound antibody-enzyme reagent, a substrate solution is added to the wells and color develops in proportion to the amount of TNF-alpha bound in the initial step. The color development is stopped and the intensity of the color is measured.

Préparation des réactifs:

Bring all reagents to room temperature before use. Wash Buffer - If crystals have formed in the concentrate, warm to room temperature and mix gently until the crystals have completely dissolved. Dilute 30 mL of Wash Buffer Concentrate into deionized or distilled water to prepare 750 mL of Wash Buffer. Standard - Reconstitute the Standard with 1.0 mL of Sample Diluent. This reconstitution produces a stock solution. Allow the standard to sit for a minimum of 15 minutes with gentle agitation prior to making serial dilutions (Making serial dilution in the wells directly is not permitted). The undiluted standard serves as the high standard. The Sample Diluent serves as the zero standard (0 ng/ml).

Prélèvement de l'échantillon: Cell culture supernates - Remove particulates by centrifugation and assay immediately or aliquot and store samples at ≤ -20 °C. Avoid repeated freeze-thaw cycles. Serum - Use a serum separator tube (SST) and allow samples to clot for 30 minutes before centrifugation for 15 minutes at approximately 1000 x g. Remove serum and assay immediately or aliquot and store samples at -20 °C. Plasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 15 minutes at 1000 x g at 2 - 8 °C within 30 minutes of collection. Store samples at ≤ -20 °C. Avoid repeated freeze-thaw cycles. Note: Citrate plasma has not been validated for use in this assay. Tissue homogenates - The preparation of tissue homogenates will vary depending upon tissue type. For this assay, heart and lung tissue from eight mice or one rat was rinsed with 1X PBS to remove excess blood, homogenized in 20 mL of 1X PBS and stored overnight at ≤ -20 °C. After two freeze-thaw cycles were performed to break the cell membranes, the homogenates were centrifuged for 5 minutes at 5000 x g. Remove the supernate and assay immediately or aliquot and store at ≤ -20 °C.

Procédure de l'essai:

Allow all reagents to reach room temperature (Please do not dissolve the reagents at 37 °C directly.). All the reagents should be mixed thoroughly by gently swirling before pipetting. Avoid foaming. Keep appropriate numbers of strips for 1 experiment and remove extra strips from microtiter plate. Removed strips should be resealed and stored at 4 °C until the kits expiry date. Prepare all reagents, working standards and samples as directed in the previous sections. Please predict the concentration before assaying. If values for these are not within the range of the standard curve, users must determine the optimal sample dilutions for their particular experiments.
1. Add 100 μL of Standard, Blank, or Sample per well. Cover with the Plate sealer. Incubate for 2 hours at 37 °C .
2. Remove the liquid of each well, don ’ t wash.
3. Add 100 μL of Detection Reagent A working solution to each well. Cover with the Plate sealer. Incubate for 1 hour at 37 °C . Detection Reagent A working solution may appear cloudy. Warm to room temperature and mix gently until solution appears uniform.
4. Aspirate each well and wash, repeating the process three times for a total of three washes. Wash by filling each well with Wash Buffer (approximately 400 μL) using a squirt bottle, multi-channel pipette, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against clean paper towels.
5. Add 100 μL of Detection Reagent B working solution to each well. Cover with a new Plate sealer. Incubate for 1 hours at 37 °C .
6. Repeat the aspiration/wash as in step 4.
7. Add 90 μL of Substrate Solution to each well. Cover with a new Plate sealer. Incubate within 30 minutes at 37 °C . Protect from light.
8. Add 50 μL of Stop Solution to each well. If color change does not appear uniform, gently tap the plate to ensure thorough mixing.
9. Determine the optical density of each well at once, using a microplate reader set to 450 nm.
Important Note:
1. Absorbance is a function of the incubation time. Therefore, prior to starting the assay it is recommended that all reagents should be freshly prepared prior to use and all required strip-wells are secured in the microtiter frame. This will ensure equal elapsed time for each pipetting step, without interruption.
2. Please carefully reconstitute Standards or working Detection Reagent A and B according to the instruction, and avoid foaming and mix gently until the crystals have completely dissolved. The reconstituted Standards can be used only once. This assay requires pipetting of small volumes. To minimize imprecision caused by pipetting, ensure that pipettors are calibrated. It is recommended to suck more than 10 μ l for once pipetting.
3. To ensure accurate results, proper adhesion of plate sealers during incubation steps is necessary. Do not allow wells to sit uncovered for extended periods between incubation steps. Once reagents have been added to the well strips, DO NOT let the 5 strips DRY at any time during the assay.
4. For each step in the procedure, total dispensing time for addition of reagents to the assay plate should not exceed 10 minutes.
5. To avoid cross-contamination, change pipette tips between additions of each standard level, between sample additions, and between reagent additions. Also, use separate reservoirs for each reagent.
6. The wash procedure is critical. Insufficient washing will result in poor precision and falsely elevated absorbance readings.
7. Duplication of all standards and specimens, although not required, is recommended.
8. Substrate Solution is easily contaminated. Please protect it from light.

Calcul des résultats:

Average the duplicate readings for each standard, control, and sample and subtract the average zero standard optical density. Create a standard curve by reducing the data using computer software capable of generating a four parameter logistic (4-PL) curve-fit. As an alternative, construct a standard curve by plotting the mean absorbance for each standard on the x-axis against the concentration on the y-axis and draw a best fit curve through the points on the graph. The data may be linearized by plotting the log of the SAA concentrations versus the log of the O.D. and the best fit line can be determined by regression analysis. It is recommended to use some related software to do this calculation, such as curve expert 13.0. This procedure will produce an adequate but less precise fit of the data. If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor.

Restrictions: For Research Use only

Stockage

Conseil sur la manipulation: 1. The kit should not be used beyond the expiration date on the kit label.
2. Do not mix or substitute reagents with those from other lots or sources.
3. If samples generate values higher than the highest standard, further dilute the samples with the Assay Diluent and repeat the assay. Any variation in standard diluent, operator, pipetting technique, washing technique,incubation time or temperature, and kit age can cause variation in binding.
4. This assay is designed to eliminate interference by soluble receptors, ligands, binding proteins, and other factors present in biological samples. Until all factors have been tested in the Immunoassay, the possibility of interference cannot be excluded.

Stock: 4 °C/-20 °C

Stockage commentaire: The Assay Plate, Standard, Detection Reagent A and Detection Reagent B should be stored at -20°C upon being received. After receiving the kit , Substrate should be always stored at 4°C.

Références pour TNF alpha Kit ELISA (ABIN456702)

Jung, Jung, Kim, Kang, Park: "Effect of KOB03, a polyherbal medicine, on ovalbumin-induced allergic rhinitis in guinea pigs." dans: Chinese medicine, Vol. 7, Issue 1, pp. 27, (2013) (PubMed).

Détail du antigène

Antigène: TNF alpha (Tumor Necrosis Factor alpha (TNF alpha))

Autre désignation: TNF (TNF alpha Produits)

Synonymes: DIF Kit ELISA, TNF-alpha Kit ELISA, TNFA Kit ELISA, TNFSF2 Kit ELISA, RATTNF Kit ELISA, Tnfa Kit ELISA, tnf Kit ELISA, TNF-a Kit ELISA, TNFalpha Kit ELISA, Tnfsf1a Kit ELISA, TNFa Kit ELISA, cTNF Kit ELISA, Tnf-alpha Kit ELISA, tnfa-like Kit ELISA, TNF-ALPHA Kit ELISA, dif Kit ELISA, tnfa Kit ELISA, xtnf Kit ELISA, tnfsf2 Kit ELISA, tnf-alpha Kit ELISA, Cachectin Kit ELISA, tumor necrosis factor Kit ELISA, tumor necrosis factor b (TNF superfamily, member 2) Kit ELISA, tumor necrosis factor alpha Kit ELISA, tumor necrosis factor a (TNF superfamily, member 2) Kit ELISA, TNF Kit ELISA, Tnf Kit ELISA, tnf Kit ELISA, tnfb Kit ELISA, tnf-alpha Kit ELISA, LOC103694380 Kit ELISA, tnfa Kit ELISA

Sujet: The prototype ligand of the TNF superfamily, TNF-alpha/TNFSF1A, is a pleiotropic cytokine that plays a central role in inflammation and apoptosis. It is synthesized as a 26 kDa, type II transmembrane protein that is 233 amino acids in length. It contains a 30 amino acid (aa) cytoplasmic domain, a 26 aa transmembrane segment, and a 177 aa extracellular region. TNF-alphais assembled intracellularly to form a transmembrane, non-covalently-linked homotrimeric protein. The 157 aa residue soluble form of TNF-alpha(sTNF-alphais released from the C-terminus of the transmembrane protein through the activity of TNF-alpha-converting enzyme (TACE), a membrane -bound disintegrin metalloproteinase. Human cells known to express TNF-alphainclude B cells, colonic columnar epithelial cells, NK and CD3+CD56+ hepatic natural T cells, macrophages, monocytes and monocyte-derived dendritic cells, CD4+ and CD8+ T cells, mast cells, neutrophils, keratinocytes, plasma cells, and adipocytes.

Pathways: Signalisation NF-kappaB, Apoptose, Caspase Cascade in Apoptosis, Signalisation TLR, Cellular Response to Molecule of Bacterial Origin, Regulation of Leukocyte Mediated Immunity, Positive Regulation of Immune Effector Process, Production of Molecular Mediator of Immune Response, Positive Regulation of Endopeptidase Activity, Hepatitis C, Protein targeting to Nucleus, Inflammasome