Thiol Quantification Assay Kit

N° du produit ABIN7384581

Détail du produit

Méthode de détection: Colorimetric

Gamme de detection: 0-16 μM

Application: Quantification (Q)

Fonction: The kit is designed to measure free thiols and disulfides in biological samples.

Type d'échantillon: Cell Extracts, Plasma, Urine

Analytical Method: Quantitative

Specificité: Specific for the detection of thiols in a variety of different biological samples.

Attributs du produit: Thiol and Disulfide Assay Kit is recommended for estimations of oxidative stress levels in biological samples such as plasma. Since many proteins contain redox-sensitive free thiols1, the identification and quantification of their different re

Ingrédients: Plate and the reagents neccesary to perform the assay.

Matériel non inclus: Pipettes, reaction tubes, plate reader.

Information d'application

Commentaires:

For native free thiols: 20μL, For disulfides: 40μL

Durée du test: 1 - 2 h

Plaque: Uncoated

Préparation des réactifs:

Reagents Preparation: Thiol and Disulfide Reagent B: Add exactly 4 mL of ultrapure water- methanol (50 % ) to the provided vial. This reagent is not stable: prepare daily and discard after use. The kit includes one vial for each 192 tests. Thiol and Disulfide Reagent D: Add exactly 4 mL of methanol to the provided vial. This reagent is not stable: prepare daily and discard after use. The kit includes one vial for each 192 tests.

Procédure de l'essai:

Thiols and Disulfide Standard: Add exactly 2 mL of diluent to the provided vial for a final concentration of 10 mM and dilute 1:10 for a final concentration of 1 mM. Then prepare different dilutions as shown below in Table 1 (see booklet). Performing the Assay: It is possible to calculate both the native (naturally reduced) and total (chemically reduced) free thiols in each sample. For the native free thiols: 1. Add 20 μL of sample/standard. 2.Add 20 μL of Thiol and Disulfide Reagent A and wait 10 min. 3. Add 220 μL of Thiol and Disulfide Reagent C and 20 μL of Thiol and Disulfide Reagent D. Wait 10 min. 4. Read the absorbance at 412 nm. For the total free thiols: 1. Add 20 μL of sample. 2.Add 20 μL of Thiol and Disulfide Reagent B and wait 10 min. 3. Add 220 μL of Thiol and Disulfide Reagent C and 20 μL of Thiol and Disulfide Reagent D. Wait 10 min. 4. Read the absorbance at 412 nm.

Calcul des résultats:

1.Zeroed the absorbance values: ?A412 nm = A412 nm sample/standard - A412 nm blank. 2.Plot the zeroed absorbance (?A412 nm) of standards as a function of their final concentrations (Table 1). See Figure 2 for a typical standard curve. 3.Calculate the free thiols value of the samples using the equation obtained from the linear regression of the standard curve substituted ?A412 nm values for each sample. 4.The reduced thiols concentration in the sample is then the free thiols value calculation for the native free thiols assay. 5.The disulfides concentration in the sample results from the difference between the free thiols value calculations for the total free thiols assay and the native free thiols assay. Free Thiols (μM) = (?A412nm - intercept) / slope

Restrictions: For Research Use only

Stockage

Agent conservateur: Sodium azide

Précaution d'utilisation: This product contains Sodium azide: a POISONOUS AND HAZARDOUS SUBSTANCE which should be handled by trained staff only.

Stock: 4 °C