Tissue factor Kit ELISA

N° du produit ABIN578945

Détail du produit Tissue factor Kit ELISA

Antigène: Tissue factor (F3) (Coagulation Factor III (thromboplastin, Tissue Factor) (F3))

Reactivité: Rat

Méthode de détection: Colorimetric

Type de méthode: Sandwich ELISA

Gamme de detection: 15.6-1000 pg/mL

Seuil minimal de détection: 15.6 pg/mL

Application: ELISA

Fonction: This immunoassay kit allows for the in vitro quantitative determination of rat TF concentrations in plasma and other biological fluids.

Type d'échantillon: Plasma

Analytical Method: Quantitative

Specificité: This assay recognizes recombinant and natural rat TF.

Réactivité croisée (Details): No significant cross-reactivity or interference was observed.

Sensibilité: The sensitivity of this assay, or Lower Limit of Detection (LLD) was defined as the lowest detectable concentration that could be differentiated from zero.

Attributs du produit: Rattus norvegicus,Rat,Tissue factor,TF,Coagulation factor III,F3,Cf3,CD142

Ingrédients: Reagent (Quantity ): Assay plate (1), Standard (2), Sample Diluent (1 × 20ml), Assay Diluent A (1x10ml), Assay Diluent B (1x10ml), Detection Reagent A (1 × 120μl), Detection Reagent B (1 × 120μl), Wash Buffer (25 x concentrate) (1 × 30ml), Substrate (1x10ml), Stop Solution (1x10ml), Plate sealer for 96 wells (5), Instruction (1)

Matériel non inclus: Luminometer. Pipettes and pipette tips. EP tube Deionized or distilled water.

Information d'application

Volume d'échantillon: 100 μL

Plaque: Pre-coated

Protocole: The microtiter plate provided in this kit has been pre-coated with an antibody specific to TF. Standards or samples are then added to the appropriate microtiter plate wells with a biotin-conjugated polyclonal antibody preparation specific for TF. Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then a TMB substrate solution is added to each well. Only those wells that contain TF, biotin-conjugated antibody and enzyme-conjugated Avidin will exhibit a change in color. The enzyme-substrate reaction is terminated by the addition of a sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450 nm 2 nm. The concentration of TF in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Préparation des réactifs:

Bring all reagents to room temperature before use. Wash Buffer - If crystals have formed in the concentrate, warm to room temperature and mix gently until the crystals have completely dissolved. Dilute 20 mL of Wash Buffer Concentrate into deionized or distilled water to prepare 500 mL of Wash Buffer. Standard - Reconstitute the Standard with 1.0 mL of Sample Diluent. This reconstitution produces a stock solution of 10000 pg/mL. Allow the standard to sit for a minimum of 15 minutes with gentle agitation prior to making serial dilutions. The undiluted standard serves as the high standard (10000 pg/mL) . The Sample Diluent serves as the zero standard (0 pg/mL). Detection Reagent A and B - Dilute to the working concentration specified on the vial label using Assay Diluent A and B (1:100), respectively.

Prélèvement de l'échantillon: Cell culture supernates - Remove particulates by centrifugation and assay immediately or aliquot and store samples at ≤ -20 °C. Avoid repeated freeze-thaw cycles. Serum - Use a serum separator tube (SST) and allow samples to clot for 30 minutes before centrifugation for 15 minutes at approximately 1000 x g. Remove serum and assay immediately or aliquot and store samples at -20 °C. Plasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 2 15 minutes at 1000 x g at 2 - 8 °C within 30 minutes of collection. Store samples at ≤ -20 °C. Avoid repeated freeze-thaw cycles. Note: Citrate plasma has not been validated for use in this assay.

Procédure de l'essai:

Allow all reagents to reach room temperature. Arrange and label required number of strips.
1. Prepare all reagents, working standards and samples as directed in the previous sections.
2. Add 100 uL of Standard, Control, or sample* per well. Cover with the adhesive strip. Incubate for 2 hours at 37 °C.
3. Remove the liquid of each well, don’t wash.
4. Add 100 uL of Detection Reagent A to each well. Incubate for 1 hour at 37°C. Detection Reagent A may appear cloudy. Warm to room temperature and mix gently until solution appears uniform.
5. Aspirate each well and wash, repeating the process three times for a total of three washes. Wash by filling each well with Wash Buffer (350 uL) using a squirt bottle, multi-channel pipette, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against clean paper towels.
6. Add 100 uL of Detection Reagent B to each well. Cover with a new adhesive strip.Incubate for 1 hours at 37 °C. 3
7. Repeat the aspiration/wash as in step
5. 8. Add 90 uL of Substrate Solution to each well. Incubate for 30 minutes at room temperature. Protect from light.
9. Add 50 uL of Stop Solution to each well. If color change does not appear uniform, gently tap the plate to ensure thorough mixing.
10. Determine the optical density of each well within 30 minutes, using a microplate reader set to 450 nm.
Important Note:1. The wash procedure is critical. Insufficient washing will result in poor precision and falsely elevated absorbance readings.
2. It is recommended that no more than 32 wells be used for each assay run if manual pipetting is used since pipetting of all standards, specimens and controls should be completed within 5 minutes. A full plate of 96 wells may be used if automated pipetting is available.
3. Duplication of all standards and specimens, although not required, is recommended.
4. When mixing or reconstituting protein solutions, always avoid foaming.
5. To avoid cross-contamination, change pipette tips between additions of each standard level, between sample additions, and between reagent additions. Also, use separate reservoirs for each reagent.
6. To ensure accurate results, proper adhesion of plate sealers during incubation steps is necessary.

Calcul des résultats:

Average the duplicate readings for each standard, control, and sample and subtract the average zero standard optical density. Create a standard curve by reducing the data using computer software capable of generating a four parameter logistic (4-PL) curve-fit. As an alternative, construct a standard curve by plotting the mean absorbance for each standard on the y-axis against the concentration on the x-axis and draw a best fit curve through the points on the graph. The data may be linearized by plotting the log of the T-PA concentrations versus the log of the O.D. and the best fit line can be determined by regression analysis. This procedure will produce an adequate but less precise fit of the data. If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor. 4.

Restrictions: For Research Use only

Stockage

Conseil sur la manipulation: 1. The kit should not be used beyond the expiration date on the kit label.
2. Do not mix or substitute reagents with those from other lots or sources.
3. If samples generate values higher than the highest standard, further dilute the samples with the Assay Diluent and repeat the assay. Any variation in standard diluent, operator, pipetting technique, washing technique,incubation time or temperature, and kit age can cause variation in binding.
4. This assay is designed to eliminate interference by soluble receptors, ligands, binding proteins, and other factors present in biological samples. Until all factors have been tested in the Immunoassay, the possibility of interference cannot be excluded.

Stock: 4 °C/-20 °C

Stockage commentaire: The Standard, Detection Reagent A, Detection Reagent B and the 96-well strip plate should be stored at -20 °C upon being received. The other reagents can be stored at 4 °C.

Références pour Tissue factor Kit ELISA (ABIN578945)

Li, Guo, Chen, Hu, Chen: "Increased plasma level of asymmetric dimethylarginine in hypertensive rats facilitates platelet aggregation: role of plasma tissue factor." dans: Canadian journal of physiology and pharmacology, Vol. 89, Issue 3, pp. 151-8, (2011) (PubMed).

Li, Peng, Xin, Luo, Zhang, Zhou, Jiang, Deng, Li: "Calcitonin gene-related peptide-mediated antihypertensive and anti-platelet effects by rutaecarpine in spontaneously hypertensive rats." dans: Peptides, Vol. 29, Issue 10, pp. 1781-8, (2008) (PubMed).

Détail du antigène

Antigène: Tissue factor (F3) (Coagulation Factor III (thromboplastin, Tissue Factor) (F3))

Autre désignation: Tissue Factor (F3 Produits)

Synonymes: CD142 Kit ELISA, TF Kit ELISA, TFA Kit ELISA, PRO1557 Kit ELISA, PRO2086 Kit ELISA, TFQTL1 Kit ELISA, f3 Kit ELISA, AA409063 Kit ELISA, Cf-3 Kit ELISA, Cf3 Kit ELISA, tf Kit ELISA, zgc:112151 Kit ELISA, coagulation factor III, tissue factor Kit ELISA, transferrin Kit ELISA, coagulation factor IIIa Kit ELISA, coagulation factor III Kit ELISA, tissue factor Kit ELISA, coagulation factor IIIb Kit ELISA, coagulation factor III (thromboplastin, tissue factor) S homeolog Kit ELISA, F3 Kit ELISA, TF Kit ELISA, f3a Kit ELISA, tf Kit ELISA, f3b Kit ELISA, f3.S Kit ELISA

Sujet: Tissue Factor is an integral membrane-bound glycoprotein (47 kD) on SDS-PAGE that requires the presence of specific phospholipids to function. It serves as both the receptor and essential cofactor(s) for VII and VIIa in initiating cell surface procoagulant activity (PCA). Once Tissue Factor was understood to initiate the extrinsic pathway of coagulation (directly activating VII that in turn activates factor X). Now, it is also known to activate factor X through the intrinsic pathway by activating factor IX which in turn activates factor X.3 The bimolecular complex of TF and factor(s) VII or VIIa activates factors IX and X by limited proteolysis, leading ultimately to thrombin generation and fibrin formation. As a potent initiator of coagulation, TF is believed to have a critical function in hemostasis and thrombogenesis. Tissue Factor, while predominantly found in lung, brain, placenta and some neoplastic tissues (e.g. breast carcinoma, melanoma), a recent investigation has shown increased Tissue Factor levels in patients diagnosed with malignant solid tumor diseases.

ID gène: 3163

Pathways: Positive Regulation of Endopeptidase Activity, Smooth Muscle Cell Migration, Platelet-derived growth Factor Receptor Signaling